# SR23C.ACQ
# 2023 April
# 2023-03-24: mbuxton and j1mclaughlin calibrated and reinstalled the AT, BP and Precip Sensors on the Mast. TSGS in main lab and bow were changed. Newer calibrated SW and PAR sensors were installed.  
# 2023-04-03: j1mclaughlin and m6thompson changed out the EE08 HRH sensor that was not reading correctly for an EE060
# 2303-04-07: j1mclaughlin and jcalderwood installed new wind sensor to replace sensor that went INOP. Removed module WND67 because it is a duplicate of WND94, it is in SR23B, if needed.  
# 2023-05-10: mrhughes added surface par to UNIT24 for CTD
#
# STS Meteorological Acquisition Program
# Serial Port and Sensor Configuration/Calibrations file
# R/V Sally Ride
#
################################################################################
# UNIT 1-2: MAINBOARD DB9 COM Ports Configuration
################################################################################
UNIT1   0 COM1    9600 NONE 8 1   # Spare
UNIT2   0 COM2    9600 NONE 8 1   # Spare
################################################################################
# UNIT 3-18: COMPUTER LAB RocketPort RJ45 COM Ports Configuration
################################################################################
UNIT3   1 COM3    9600 NONE 8 1   # RS232 Input  - MET Mast sensors
UNIT4   1 COM4    9600 NONE 8 1   # RS232 Input  - SBE48 Hull Temperature Sensor
UNIT5   1 COM5    9600 NONE 8 1   # RS232 Input  - 2017/7 - Hemisphere above winch shack
UNIT6   1 COM6    9600 NONE 8 1   # RS232 Input  - Bow Wind
UNIT7   1 COM7   19200 NONE 8 1   # RS232 Input  - Seapath VRU
UNIT8  20 COM8    9600 NONE 8 1   # RS232 Output - OUT08 to X-band Radar
UNIT9  20 COM9    4800 NONE 8 1   # RS232 Output - OUT09 temp gyro output to splitter
UNIT10  1 COM10   9600 NONE 8 1   # RS232 Input  - ADCP currents speedlog
UNIT11  1 COM11   9600 NONE 8 1   # RS232 Input  - SBE45 (Bow Thruster Rm)
UNIT12  1 COM12  19200 NONE 8 1   # RS232 Input  - Seapath GPS
UNIT13 20 COM13   9600 NONE 8 1   # RS232 Output - MET data to PCO2
UNIT14  4 COM14   9600 NONE 8 1   # RS232 Output - MET Data out $WICOR
UNIT15  1 COM15   9600 NONE 8 1   # RS232 Input  - Hydrins navbho
UNIT16  1 COM16  19200 NONE 8 1   # RS232 Input  - Hydrins GPS-like
UNIT17  0 COM17   9600 NONE 8 1   # RS232 
UNIT18  1 COM18   9600 NONE 8 1   # RS232  
UNIT19  20 COM19 19200 NONE 8 1   # RS232 Output - MET SV to EM124 and EM712
UNIT20  1 COM20  19200 NONE 8 1   # RS232 Input  - Trawl Winch 
UNIT21  1 COM21  19200 NONE 8 1   # RS232 Input  - Hydro Winch Aft 
UNIT22  1 COM22  19200 NONE 8 1   # RS232 Input  - Hydro Winch Forward 
UNIT23  1 COM23   9600 NONE 8 1   # RS232 Input  - SeaSpy Magnetometer(s)
UNIT24 14 COM24   9600 NONE 8 1   # RS232 Output - Surf PAR to SBE11
UNIT25  0 COM25   4800 NONE 8 1   # Spare
UNIT26  1 COM26  19200 NONE 8 1   # RS232 Input  - CTD Depth,Spd,Alt
UNIT27  1 COM27   1200 NONE 8 1   # RS232 Input  - BGM-3 gravimeter counts
UNIT28  0 COM28   9600 NONE 8 1   # Spare
UNIT29 20 COM29   9600 NONE 8 1   # RS232 Output - MB Depth Marchetti
UNIT30 20 COM30   9600 NONE 8 1   # RS232 Output - OUT30 to pCO2 
UNIT31 20 COM31   4800 NONE 8 1   # RS232 Output - OUT66 to pCO2
UNIT32 20 COM32   4800 NONE 8 1   # RS232 Output - OUT32 to MVP for Ohman/Landry cruises
UNIT33  0 COM33   9600 NONE 8 1   # Spare
UNIT34  0 COM34   9600 NONE 8 1   # Spare
#
################################################################################
# UNIT 36-43: MAIN LAB COM-via-net Serial Ports Configuration
# Commented out line 61 UNIT43 - TEMP GGA OUT for CALCOFI
################################################################################
UNIT36  1 COM36   9600 NONE 8 1   # RS232 Input  - Main Lab Flo-thru system
UNIT37  1 COM37  19200 NONE 8 1   # RS232 Input  - FLUNTS
UNIT38  1 COM38  19200 NONE 8 1   # RS232 Input  - ECO Triplet-w
UNIT39  1 COM39   9600 NONE 8 1   # RS232 Input  - SBE63
UNIT40  1 COM40   9600 NONE 8 1   # RS232 Output - SR2001 Temp GGA
UNIT41  0 COM41   9600 NONE 8 1   # Spare 
UNIT42 20 COM42   9600 NONE 8 1   # RS232 Output - SR1909-11 Ship Data Temp
UNIT43 20 COM43   9600 NONE 8 1   # RS232 Output - SR2001 Temp GGA
#
################################################################################
# UNIT 64-127: UDP/IP datagram modules
# As practical, Source port = Destination port - 1
# Do not use the same UDP port number more than once.
################################################################################
UNIT64  0 UDP    40009 NONE 40008 100.124.101.255     # Spare
UNIT65 19 UDP    40019 NONE 40018 100.124.101.255     # Output - $WICOR to Acq-LAN subnet broadcast
UNIT66 81 UDP    40183 NONE 40182 100.124.101.255     # Output - OUT66 to Acq-LAN subnet broadcast
UNIT67 80 UDP    55000 NONE NONE   		     # Input  - Knudsen 3260 UDP feed from Acq-LAN subnet broadcast
UNIT68 80 UDP    28002 NONE NONE   		     # Input  - Trimble UDP feed from Acq-LAN subnet broadcast
#UNIT71 81 UDP    40193 NONE 40031 100.124.100.255    # Output - GPS/HDG to Main-LAN subnet broadcast    
#UNIT72 81 UDP    40194 NONE 40032 100.124.100.255    # Output - GPS/HDG to Main-LAN other subnet broadcast    
#UNIT73 19 UDP	 40019 NONE 40020 100.124.100.255    # Output - $WICOR to Main-LAN other subnet broadcast
UNIT79 80 UDP     9133 NONE NONE                     # Input  - UHDAS Speed Log VBW Message DAS-LAN subnet broadcast
UNIT81 81 UDP     9713 NONE 9712  100.124.101.255     # Output - OUT11 to EM124 and EM712
UNIT82 80 UDP    16185 NONE NONE                     # Input  - EM712 depth DAS-LAN subnet broadcast
UNIT83 80 UDP    16187 NONE NONE                     # Input  - EM124 depth DAS-LAN subnet broadcast
UNIT88 81 UDP    19991 NONE 19990 100.124.101.255    # Output - MET feeds to pCO2
#
################################################################################
# Module initialization, in order of preference.
#	Any defined Output modules should be listed here.  To disable, set 
#	SERUNITNUM = 0 in the module itself.
#	Add OUT42 for the GGA, GLL, RMC output to the mammal hydrophone 
#	people on line 108 CALCOFI, under the STARDMOD
################################################################################ 
STARTMOD
	TMP29 BPR85 HRH10 HRH21 VLT01 #PRC64
	WND94
	LWR36 SWR36 PAR70
	SOW01	# UHDAS speedlog
	NME01	# Seapath 330+
	NME02	# Trimble
	NME03	# Hydrins
	SND01	# Knudsen 3260
	MBD02   # EM124 Center Beam Depth
        MBD01   # EM712 Center Beam Depth
	IST01	# CTD Depth
	#	BOW SBE45, TSG_Flow, PCO2_Flow
	TSG86 FLW19 FLW20
	SST62	# Transducer Void SBE48
	#	Main lab SBE45, TSG_FLOW, O2, Fluorometer#1_FlUNTS, Fluorometer#2_WetStar, Transmissometer
	TSG73 FLW09 OXY66 OXY99 FLU02 FLU97 XMS76
#	FLU81
#	VRU16
	GYR02   # Seapath
	GYR01   # Trimble
	GYR04   # Hemisphere V104S
	GYR05   # Hydrins
	GRV01   # gravimeter counts
	WCH01   # Cast6, forward
	WCH02	# Cast6, aft
	WCH03	# Traction winch
#	USP01   # CalCOFI pco2
	OUT13 OUT43 OUT42
	OUT50   # Marchetti MB depth
	OUT30   # output for pCO2
	OUT66 OUT71 OUT09 OUT73
	OUT08 OUT66 OUT71 OUT72 OUT09 OUT11 OUT19
	OUT40   # GGA SR2001
#	OUT98   # GGA,RMC SR1913
#       OUT99   # GGA SR1913
	MAG01
#       OUT32 # Ohman MVP cruises
	UCW01
ENDMOD
################################################################################

[GENERAL]
	# Do not rely on ntp.rv-sallyride.ucsd.edu for time sync (system settings).
	# While the time server is accurate, Windows updates too infrequently
	# to avoid clock drift.
	GPS_SYNCH		= TRUE
#	SET_TRACE = TRUE

	# Write data to directories, e.g. C:\MET\SR1605, based on the contents
	# of C:\MET\cruisename.txt
	MKCRUISEDIRS		= TRUE

	########################################################################
	# Surface PAR to CTD Config
	########################################################################

	SPARSCL = 1000.0, 0.0

	########################################################################
	# Vessel Info
	########################################################################
	TITLE			= R/V Sally Ride MET System
	CALL_SIGN		= WSAF
	SHIP			= RIDE
	RADIO_CALL_SIGN		= WSAF

	########################################################################
	# Write settings
	########################################################################
	PRINT_EN		= FALSE
	MK_COR			= TRUE
	MK_UNC			= TRUE
	MK_LOG			= TRUE
	MK_DCC			= TRUE
	DCC_INTERVAL		= 60.0
#	Change interval to 1.0 sec for SR1911 - hkj
# For FLEAT and Graber cruises, e.g., SR1716 Colosi
	FileWriteInterval       = 15.0
	SerialWriteInterval	= 15.0
	TIMEOUT			= 400
	ONEGPS2FILE		= FALSE
	MAX_SCAN_RATE		= 10.0
	CHART_RATE		= 2

	########################################################################
	# Global E-mail settings
	########################################################################
	# If configured, use local IIS SMTP service to relay mail
	# to ship's SMTP server.
	#
	# As long as the MET is on private IP space, set IIS SMTP Server
	# Properties to General->IP address to "(All Unassigned)".
	# This will enable localhost delivery.
#	#MAIL_SERVER		= 127.0.0.1
	# If not, use shipboard SMTP server; not used for better performance
	MAIL_SERVER		= 127.0.0.1
	MAIL_RETADD		= sts-cr@ucsd.edu

	########################################################################
	# SIO shiptrack E-mail settings.
	# NOTE: you must also set the cruisename in C:\MET\cruisename.txt
	########################################################################
# Currently Shiptrack is not accepting email.
#	SHIPTRACK_RECEP		= sio-shiptracks@ucsd.edu

	########################################################################
	# SAMOS and NOAA E-mail Settings
	########################################################################
	MAIL_NOAA		= webship@noaa.gov
	MAIL_RECEP		= samos_data@coaps.fsu.edu

		################################################################
		# Note the following SAMOS locations for module configuration:
		# E.G. SAMOS_LD	= B
		################################################################
		# B = Bow mounted MET Mast
		# D = Bow mounted MET Mast 2nd sensor
		# U = UCW intake area
		# A = Aft (stern weather deck)
		# P = Port
		# S = Starboard
		# N = Main Lab

#		 Winch Names
	WID1	= CAST6-fwd Winch,0
	WID2	= CAST6-aft Winch,1
	WID3	= Traction Winch,2
	WID4	= Traction Winch #2,3

################################################################################
# Customized output modules, in alphanumeric order.
# Add [OUT42] module for the custom NMEA output from the serial box 
# in the main lab, lines 226-230 CALCOFI
################################################################################

[OUT08]	# DESCRIPTION: Wind Data Output for WAMOS
	SERUNITNUM		= 8
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	NMEA			= MWV, MWD

[OUT09]	# DESCRIPTION: 1Hz NMEA 0183 heading. Temp SR1710
	SERUNITNUM		= 09
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	NMEA			= HDT

[OUT11] # DESCRIPTION: EM124 and EM712 AML SV&T (C+T) sound speed derived from TSG.
        SERUNITNUM        = 19,81
        PARAMETERS        = TT, SV
        # Change to 0,0 for Bow Thruster; 1,1 for Main Lab
        PARAMETER NUMBERS = 0, 0
        #PARAMETER NUMBERS = 1, 1
        PRECISION         = 3, 1
        MKOUTFILE         = FALSE
        INTERVAL          = 1.0
        FORMAT            = %7.3f %7.1f

[OUT13]
	SERUNITNUM		= 13
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	PARAMETERS		= FI TT SA FI FI ST AT BP GY SP
	PARAMETER NUMBERS	= 0 1 1 1 2 0 0 0 0 0
	DELIMITERS		= ,
	ADDTIMESTAMP            = FALSE
	ADDCRC			= FALSE

[OUT19] # DESCRIPTION: EM124 and EM712 AMLsound speed derived from TSG.
        SERUNITNUM        = 19,81
        PARAMETERS        = TT, SV
        # Change to 0,0 for Bow Thruster; 1,1 for Main Lab
        PARAMETER NUMBERS = 0, 0
        #PARAMETER NUMBERS = 1, 1
        PRECISION         = 3, 1
        MKOUTFILE         = FALSE
        INTERVAL          = 1.0
        FORMAT            = %7.3f %7.1f

[OUT30] # DESCRIPTION: MET data for pCO2
        SERUNITNUM        = 30,88
        MKOUTFILE         = FALSE
        INTERVAL          = 1.0
        PARAMETERS        = FI TT SA FI FI ST AT BP GY SP OX
        PARAMETER NUMBERS = 0 1 1 1 2 0 0 0 0 0 0
        DELIMITERS        = ,
        ADDTIMESTAMP      = FALSE
        ADDCRC            = FALSE

[OUT32] # DESCRIPTION: 1Hz NMEA for Ohman/Landry cruises with MVP
        SERUNITNUM              = 32
        MKOUTFILE               = FALSE
        INTERVAL                = 1.0
        NMEA                    = GGA,ZDA,VHW,DBS

[OUT40] # DESCRIPTION: GGA OUT.  Temp SR2001
        SERUNITNUM              = 40
        MKOUTFILE               = FALSE
        INTERVAL                = 1.0
        NMEA                    = GGA

[OUT42]	# DESCRIPTION: 1Hz SHIP DATA. Temp SR1909
	SERUNITNUM		= 42
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	PARAMETERS		= LA LO CR SP GY AT RH TI TW WD WS TT SA BP SW LW LB LD PR
        FORMAT			= LA: %.4f LO: %.4f CR: %.2f SP: %.2f GY: %.4f AT: %.4f RH: %.4f TI: %.4f TW: %.4f WD: %.4f WS: %.4f TT: %.4f SA: %.4f BP: %.4f SW: %.4f LW: %.4f LB: %.4f  LD: %.4f PR: %.2f
	ADDTIMESTAMP            = TRUE

[OUT43]	# DESCRIPTION: GGA Temp SR2001
	SERUNITNUM		= 43
	MKOUTFILE               = FALSE
        INTERVAL                = 1.0
        NMEA                    = GGA

[OUT50] # DESCRIPTION: Marchetti MB DEPTH for trace metal CTD deck unit
	SERUNITNUM		= 29
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	NMEA			= GGA,DPT


[OUT66]	# DESCRIPTION: 1Hz NMEA 0183 position/heading for UDP and RS232.
	SERUNITNUM		= 31,66
	MKOUTFILE		= TRUE
	INTERVAL		= 1.0
	NMEA			= GGA,VTG,ZDA,HDT

[OUT99]	# DESCRIPTION: 1Hz NMEA 0183 position/heading for UDP and RS232.
	SERUNITNUM		= 41
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	NMEA			= GGA,ZDA,VTG,HDT

[OUT98]	# DESCRIPTION: 1Hz NMEA 0183 position/heading for UDP and RS232.
	SERUNITNUM		= 40
	MKOUTFILE		= FALSE
	INTERVAL		= 1.0
	NMEA			= ZDA,GGA,VTG,HDT,RMC


[OUT71] # DESCRIPTION: 1Hz NMEA 0183 position/heading for UDP and RS232. 
        SERUNITNUM              = 71
        MKOUTFILE               = FALSE
        INTERVAL                = 1.0
        NMEA                    = GGA,VTG,ZDA,RMC,HDT

[OUT72] # DESCRIPTION: 1Hz NMEA 0183 position/heading for UDP and RS232.
        SERUNITNUM              = 72
        MKOUTFILE               = FALSE
        INTERVAL                = 1.0
        NMEA                    = GGA,VTG,ZDA,RMC,HDT

################################################################################
# Sensor modules, in alphanumeric order.
################################################################################

[MAG01]
	SENSOR		= Magnetometer
	MODEL		= SeaSpy
	SERIAL		= ?????
	MFG		= Geometrics
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Towed Fish, 300m, 600m or 700m behind the ship.
	OWNER		= SIO/STS
	DCC		= FALSE
	# Module setup parameters
	MSP		= 23 21 0 0 10 0 6  1 2 3 4 5 6 0 0
	MCP		= 1   1 6 0  0 0 0 0 0 0 0 0
	# Emulation value(s) can be Mag Mode, e.g.:
	# *12.118/07:49:28.0 F:029129.131 S:184 D:+001.1m  L0 0965ms Q:99  
	# ... or Grad Mode, e.g.:
	# *12.127/03:43:32.5 F[024996.573 153 0466 +0033.5 ___] R[024996.263 158 0466 +0023.5 ___] +000000.310
	Emulation       = 026452.728, 35.0, 150 0 0 0
	# A/D Calibration
	ADCAL		= 1,0.0
	# Corrections RH
	COR		= 1.0,0.0
	# Corrections RT
	COR2		= 1.0,0.0

[SOW01]
        SENSOR          = Speed Log
        MODEL           = UHDAS (WH300)
 	SERIAL		= 24625
#       SERIAL          = 41899 (OS150)
        MFG             = RDI
        LOCATION        = TRANSCEIVER ROOM
        OWNER           = SIO-STS
        DCC             = FALSE
        TAGS-R          = SL, SX
        TAGS-C          = SL, SX
        ## Module setup parameters
#	MSP		= 79 14
        MSP             = 10 8
        # $VDVBW,13.53,0.20,A,,,*26
        ## Emulation Value
        Emulation       = 1.0 -0.01

[BPR85]
	SENSOR		= Barometric Pressure
	MODEL		= 61302V
	SERIAL		= BPA2467
	MFG		= RM Young
	CAL_LAB		= STS Cal Lab
	CAL_DATE	= 22-Mar-2023
	LOCATION	= MET Mast 46.5'above DWL
	INSTALL_DATE	= 23-Mar-2023
	OWNER		= SIO/STS
	DCC		= TRUE
	SAMOS_LD	= B
	## Module address
	CMD		= #02\r
	## Module setup parameters
	MSP		= 3 2 0 0 13 0 1 7 0 0 0 0 0 0 0
	MCP		= 1 1 2 0 13 37 0 0 0 0 0 0
	## Emulation Value
	Emulation	= 2.8739 # 1014.4233
	AVGTYPE		= 1
	SECSTOAVG	= 60.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR             =  3.98936467E+1 8.99624141E+2
        ## Altitude of sensor above water line in Meters
	COR2		= 15.24

[TMP29]
	SENSOR		= Air Temperature
	MODEL		= 41342VC
	SERIAL		= 27718
	MFG		= RM Young
	CAL_LAB		= STS
	CAL_DATE	= 23-Mar-2023
	LOCATION	= MET Mast 46.5'above DWL
	OWNER		= SIO/STS
	INSTALL_DATE	= 23-Mar-2023
	DCC		= TRUE
	SAMOS_LD	= B
	## Module address
	## Adam 4117 Channel #4 (counting from 0)
	CMD		= #02\r
	## Module setup parameters
	MSP        = 3 2 0 0 13 0 1  5 0 0 0 0 0 0 0
	MCP		= 1 1 1 0 5 0 0 0 0 0 0 0
	Emulation	= 0.7568
	AVGTYPE		= 1
	SECSTOAVG	= 60.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR		= 9.97371858E+1 -4.9974860E+1

[HRH10]
        SENSOR          = Relative Humidity
        MODEL           = EE060
        SERIAL          = S99736
        MFG             = E+E ELEKTRONIK
        CAL_LAB         = STS Cal Lab
        CAL_DATE        = 29-Nov-2022
        LOCATION        = MET Mast 46.5' above DWL
        INSTALL_DATE    = 03-Apr-2023
        OWNER           = SIO/STS
        DCC             = TRUE
        SAMOS_LD        = B
        DCC_MASK        = 1,1,0,0,0,0,0,0
        # Module address
        CMD             = #02\r
        # Module setup parameters
        MSP             = 3 2 0 0 13 0 2  1 2 0 0 0 0 0 0
        MCP             = 1 1 3 0 5 13 15 0 0 0 0 0
        # Emulation value
        Emulation       = 0.6 0.6
        AVGTYPE         = 1 1 0
        SECSTOAVG       = 60.0
        # A/D Calibration
        ADCAL           = 1.0 ,0.0
        # Corrections RH
        COR             = 1.91480236E+0 1.05398997E+2 -1.98030843E+0
        # Corrections RT
        COR2            = 1.00797578E+2 -4.04110460E+1

[HRH21]
	SENSOR		= Relative Humidity
	MODEL		= EE08
	SERIAL		= 17330500010121
	MFG		= E+E ELEKTRONIK
	CAL_LAB		= STS Cal Lab
	CAL_DATE	= 29-Nov-2022
	LOCATION	= MET Mast 46.5' above DWL
	INSTALL_DATE	= 01-Dec-2022
	OWNER		= SIO/STS
	DCC		= TRUE
	SAMOS_LD	= D
	DCC_MASK	= 1,1,0,0,0,0,0,0
	# Module address
	CMD		= #02\r
	# Module setup parameters
	MSP		= 3 2 0 0 13 0 2  3 4 0 0 0 0 0 0
	MCP		= 1 1 3 0  5 13 15 0 0 0 0 0
	# Emulation value
	Emulation	= 0.6 0.6
	AVGTYPE		= 1 1 0
	SECSTOAVG	= 60.0
	# A/D Calibration
	ADCAL		= 1.0 ,0.0
	# Corrections RH
	COR		= 1.45100283E+1 8.79035056E+1 -1.14420256E-1
	# Corrections RT
	COR2		= 1.00928007E+2 -4.05255792E+1

[VLT01]
	SENSOR		= Fan Aspirator
	MODEL		= LAM630
	SERIAL		= 20226
	MFG		= Eigenbrodt
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= MET Mast 46.5'above DWL
	INSTALL_DATE	= 20-May-2020
	OWNER		= SIO/STS
	LABELS-TAB      = ASPIRATOR
        LABELS-SC       = FAN
	DCC		= TRUE
	SAMOS_LD	= B
	# if fan is running then the value is greater than 2 otherwise it is not running.
	CMD = #04\r
	## Module setup parameters
	MSP		= 3 2 0 0 13 0 1  1 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  0 0 0 0 0 0 0 0
	## Emulation value
	Emulation	= 2.5
	COR		= 1.0, 0.0

[PRC64]
	SENSOR		= Precipitation
	MODEL		= 50202
	SERIAL		= 02364
	MFG		= RM Young
	CAL_LAB		= RM Young
	CAL_DATE	= 22-Mar-2023
	LOCATION	= MET Mast 46.5'above DWL
	INSTALL_DATE	= 23-Mar-2023
	OWNER		= SIO/STS
	DCC		= TRUE
	SAMOS_LD	= B
	CMD		= #02\r
	## Module setup parameters
	MSP		= 3 2 0 0 13 0 1  6 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  13 0 0 0 0 0 0 0
	## Emulation value
	## mm/min, mm/hr, mm
	Emulation	= 4.360  ##45.220
	## A/D Calibration
	ADCAL		= 1.0, 0.0
	## Corrections
	COR		= 1.04814011E+1 -8.06002569E-1

[WND94]
        SENSOR          = WIND
        MODEL           = 85106
        SERIAL          = 01994
        MFG             = RM Young
        CAL_LAB         = RM Young
        CAL_DATE        = ??
        LOCATION        = MET Mast 47.5'above DWL
        INSTALL_DATE    = 07-Apr-2023
        OWNER           = SIO/STS
        DCC             = TRUE
        SAMOS_LD        = B
        TLD             = Bow
        SLD             = BW
        ## Module address
	## Uncomment when using the j-box run:
        CMD            = #Z9R0\r
        ## Module setup parameters
	## Uncomment when using the j-box run; comment out when using direct run:
        MSP            = 3 0 0 0 10 0 2  4 2 0 0 0 0 0 0
        ## Uncomment when using the direct run; comment out when using the j-box:
	#MSP             = 6 8
        MCP             = 1 1 4 0 0 0 19 20 0 0 0 0
        ## Emulation value
        Emulation       = 6.0 10.0
        AVGTYPE         = 1 2 0 0
        SECSTOAVG       = 60.0
        ## A/D Calibration
        ADCAL           = 1.0 0.0
        ## Corrections Wind Speed
        COR             = 1.0, 0.0
        ## Corrections Wind Direction
        COR2            = 0.0, 0.0

[IST01]
	SENSOR		= CTD Depth
	MODEL		= SBE11
	SERIAL		= XXXX
	MFG		= Seabird
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= 01 Lab
	OWNER		= SIO/STS
	DCC		= FALSE
	## CTD Depth, Rate of descent, Altimeter
	TAGS-C		= IP, IV, IA
	TAGS-R		= IP, IV, IA
	PRC-C		= 2, 4, 1
	PRC-R		= 2, 4, 1
	RANGE		= -10.0 15000.0
	RANGE2		= -200.0 200.0
	RANGE3		= -10.0 500.0
	## Module setup parameters
	MSP		= 26 3 0 0 10 0 3  1 2 3 4 5 0 0 0
	MCP		= 0 1 3 0  0 3 0 0 0 0 0 0
	AVGTYPE		= 0 1 0
	SECSTOAVG	= 10.0
	## Emulation Value
	## Depth, Speed, Altimeter
	Emulation	= 1500.0 0.95 45.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR		= 0.0 0.0
	COR2		= 60.0 0.0
	COR3		= 0.0 0.0

[LWR36]
	SENSOR		= Long Wave Radiation
	MODEL		= PIR
        SERIAL          = 38302F3 
	MFG		= Eppley Labs
	CAL_LAB		= Eppley
	CAL_DATE	= 6 FEB-2020
	LOCATION	= MET Mast 50'above DWL
	OWNER		= SIO/STS
	INSTALL_DATE	= 27 OCT-2022
	DCC		= TRUE
	DCC_MASK	= 0,0,0,1,0,0,0,0
	SAMOS_LD	= B
	# ADAM 4118 0-15mv Thermopile CH2, 0-2.5VDC Dome CH4, Body CH5 (ACQ calls the first channel CH1; Advantech calls it CH0)
	CMD		= #04\r
	# Module setup parameters
	MSP            = 3 2 0 0 13 0 3 4 5 2 0 0 0 0 0 body temp and dome temp
        # MSP          = 3 2 0 0 13 0 3 5 5 2 0 0 0 0 0 

	MCP		= 1 0 4 0  9 9 3 8 0 0 0 0
	# Emulation values
	Emulation	= 0.7568 0.7568 0.1147
	# A/D Calibration
	ADCAL		= 1.0 0.0
	# Dome, Body, Thermopile
	# Corrections for Dome Glass Temp sensor
	COR		= 5.0, 82500, 0.0010295, 0.0002391, 1.568e-7, 1.0, 0.0
	# Corrections for Body Temp sensor
	COR2		= 5.0, 82500, 0.0010295, 0.0002391, 1.568e-7, 1.0, 0.0
	# Eppley correction factors
	# Thermopile Slope Offset (in uv)
	COR3		= 1000.0, 0.0
	# Eppley factor, Stefan-Boltzmann Const, absorption/dome glass IR
	# Cal Factor  volts/watts meter -2
	COR4		= 2.89e-6

[PAR70]
	SENSOR		= Surface PAR
	MODEL		= QSR-2200
	SERIAL		= 20226
	MFG		= Biospherical Instruments
	CAL_LAB		= Biospherical Instruments
	CAL_DATE	= 29-Jul-2022
	LOCATION	= MET Mast 50'above DWL
	INSTALL_DATE	= 23-Mar-2023
	OWNER		= SIO/STS
	DCC		= TRUE
	SAMOS_LD	= B
	CMD 		= #02\r
	PRC-C		= 2
	PRC-R		= 3
	## Module setup parameters
	MSP 		= 3 2 0 0 13 0 1 8  0 0 0 0 0 0 0
	MCP		= 1 1 1 3  13 0 0 0 0 0 0 0
	## Emulation value
	Emulation	= 1.0
	AVGTYPE		= 1
#	SECSTOAVG	= 30.0
	## A/D Calibration
	ADCAL		= 1.04464, 0.0
	## Corrections Surface PAR V/(MicroEinsteins/sec/cm2)
	## Slope, Offset, scale
	COR		= 1316.15 0.0

[SWR36]
	SENSOR		= Short Wave Radiation
	MODEL		= SPP
	SERIAL		= 38363F3
	MFG		= Eppley Labs
	CAL_LAB		= Eppley Labs
	CAL_DATE	= 05-Feb-2020
	LOCATION	= MET Mast 50'above DWL
	INSTALL_DATE	= 23-Mar-2023
	OWNER		= SIO/STS
	DCC		= TRUE
	SAMOS_LD	= B
	# ADAM 4118 0-100mv CH3 (ACQ calls the first channel CH1; Advantech calls it CH0)
	# Module address
	CMD		= #04\r
	PRC-C		= 2
	PRC-R		= 3
	# Module setup parameters
	MSP		= 3 2 0 0 13 0 1  3 0 0 0 0 0 0 0
	MCP		= 1 1 1 3  26 0 0 0 0 0 0 0
	# Emulation value
	Emulation	= 1.5
	# A/D Calibration
	ADCAL		= -1.0,0.0
	# Slope, Offset, Cal Factor
        COR             = 1e-3,0.040,7.82e-6

[NME01]
	SENSOR		= GPS
	MODEL		= Seapath 330+
	SERIAL		= 11700
	MFG		= Kongsberg
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	INSTALL_DATE	= 2016-Jul-01
	LOCATION	= Main Mast
	OWNER		= SIO/STS
	DCC		= FALSE
	DCC_MASK	= 1,1,0,1,1,0,0,0
	SAMOS_LD	= E
	## Module setup parameters
	MSP		= 12 8
	## Emulation Value
	Emulation	= 32.25 -117.86 4000.0 90.0 12.0 1018724200.0 25.0 207.0

[NME02]
	SENSOR		= GPS
	MODEL		= BD982
	SERIAL		= 5529C00326
	MFG		= Trimble
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	INSTALL_DATE	= 2016-Jul-01
	LOCATION	= Main Mast
	OWNER		= SIO/STS
	DCC		= TRUE
	DCC_MASK	= 1,1,0,1,1,0,0,0
	SAMOS_LD	= E
	## Module setup parameters
	MSP		= 68 14
	## Emulation Value
	Emulation	= 32.25 -117.86 4000.0 90.0 12.0 1018724200.0 25.0 207.0

[NME03]
        SENSOR          = GPS
        MODEL           = Hydrins
        SERIAL          = PH-490
        MFG             = iXBlue
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        INSTALL_DATE    = 2016-Jul-01
        LOCATION        = Transducer Room, with feed from Trimble BD982
        OWNER           = SIO/STS
        DCC             = FALSE
	DCC_MASK	= 1,1,0,1,1,0,0,0
        ## Module setup parameters
        MSP             = 16 8
        ## Emulation Value
        Emulation       = 32.25 -117.86 4000.0 90.0 12.0 1018724200.0 25.0 207.0

[GRV01]
        SENSOR          = Gravimeter
        MODEL           = BGM-3
        SERIAL          = S224
        MFG             = Bell Aerospace
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        LOCATION        = Transceiver Room
        DCC             = FALSE
        SAMOS_LD        = L
        INSTALL_DATE    = 26-Jan-2017
        OWNER           = SIO/STS
        # Module setup parameters
        MSP             = 27 22 0 0 10 0 1  1 0 0 0 0 0 0 0
        MCP             = 1 1 1 0  0 0 0 0 0 0 0 0
        # Emulation Value 01:024843 00
        Emulation       = 024843
        ADCAL           = 1,0.0
        COR             = 1.0,0.0
[GYR01]
        SENSOR          = Gyro
        MODEL           = BD982
        SERIAL          = 5529C00326
        MFG             = Trimble
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        INSTALL_DATE    = 2016-Jul-01
        LOCATION        = Aft wheelhouse
        OWNER           = SIO/STS
        DCC             = FALSE
        # Module setup parameters
        MSP             = 68 14
        Emulation       = 281.0
        MCP             = 1 1 1 0  0 0 0 0 0 0 0 0
        COR             = 0.0

[GYR02]
    	SENSOR        	= Gyro
    	MODEL        	= Seapath 330+
    	SERIAL        	= 11700
    	MFG        	= Kongsberg
    	CAL_LAB        	= n/a
    	CAL_DATE    	= n/a
    	INSTALL_DATE    = 2016-Jul-01
    	LOCATION    	= Aft wheelhouse
    	OWNER        	= SIO/STS
    	DCC        	= TRUE
	SAMOS_LD        = B
    	# Module setup parameters     
    	Emulation    	= 279.0
    	MSP        	= 12 8
    	MCP        	= 1 1 1 0  0 0 0 0 0 0 0 0
    	COR        	= 0.0

[GYR04]
        SENSOR          = Gyro
        MODEL           = MV104S, 804-0114-0 Rev B1
        SERIAL          = C1436-00182-02-670
        MFG             = Hemisphere
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        LOCATION        = Above winch shack
        OWNER           = SIO/STS
        INSTALL_DATE    = 25-Jul-2017
        DCC             = FALSE
        SAMOS_LD        = B
        #CMD = $HEHDT\r\n
        # Module setup parameters
        Emulation       = 279.0
        MSP             = 5 8
        MCP             = 1 1 1 0  0 0 0 0 0 0 0 0
        COR             = 0.0

[GYR05]
        SENSOR          = Gyro
        MODEL           = Hydrins
        SERIAL          = PH-490
        MFG             = iXBlue
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        LOCATION        = Transducer Room, with feed from Trimble BD982
        OWNER           = SIO/STS
        DCC             = FALSE
        #CMD = $HEHDT\r\n
        # Module setup parameters
        Emulation       = 279.0
        MSP             = 15 8
        MCP             = 1 1 1 0  0 0 0 0 0 0 0 0
        COR             = 0.0

[VRU16]
    	SENSOR		= Vertical Reference Unit
    	MODEL		= Seapath 330+
    	SERIAL		= 11700
    	MFG		= Kongsberg
    	CAL_LAB		= n/a
    	CAL_DATE	= n/a
    	LOCATION	= VRU Plate
    	INSTALL_DATE	= 01-Jul-2016
    	OWNER    	= SIO/STS
    	DCC     	= FALSE
    	# Module address
    	TAGS-C		= VP VR VH GY
    	TAGS-R		= VP VR VH GY
    	PRC-C		= 2 2 2 2
    	PRC-R		= 2 2 2 2
    	# Module setup parameters
    	MSP		= 7 7 0 0 10 0 4  1 2 3 6 0 0 0 0
    	MCP		= 1 1 4 0  0 0 0 0 0 0 0 0
    	# Emulation value
    	Emulation	= 2.0 5.0 0.5 128.0
    	# A/D Calibration
    	ADCAL		= 1.0 0.0
    	COR		= 1.0 0.0
    	COR2		= 0.0
    	COR3		= 0.0
    	COR4		= 0.0

[SND01]
        SENSOR          = Depth
        MODEL           = 3260
        SERIAL          = K2K-14-0546
        MFG             = Knudsen
        LOCATION        = Xcvr Room
        INSTALL_DATE    = 2016
        OWNER           = SIO/STS
        CMD             = PKEL
        DCC             = FALSE
        DCC_MASK        = 1,0,0,0,0,0,0,0
        # Module setup parameters
        MSP             = 67 14
        MCP             = 0 1 3 0  1 0 0 0 0 0 0 0
        # Emulation Value
        Emulation       = 1550.0 1600 1700
        # A/D Calibration
        ADCAL           = 1.0 0.0
        # Corrections
        COR             = 0.0,0.0

[TSG86]
        SENSOR          = Thermosalinograph
        MODEL           = SBE45
        SERIAL          = 0083
        MFG             = Seabird
        CAL_LAB         = Seabird
        CAL_DATE        = 08-Nov-2022
        LOCATION        = Bow thruster UCW intake
        INSTALL_DATE    = 22-Mar-2023
        OWNER           = SIO/STS
        DCC             = TRUE
	DCC_MASK	= 1,1,1,0,0,0,0,0
        SAMOS_LD        = L
        LABELS-TAB      = TSG_Temp_BW,TSG_Cond_BW, Salinity_BW,SigmaT_BW,SoundVel_BW,TSG_RCond_BW
        LABELS-SC       = TT_BW,TC_BW, Sal_BW,SgT_BW,SV_BW,TRC_BW
        ## Module setup parameters
        MSP             = 11 3 0 0 10 0 2  2 3 0 0 0 0 0 0
        MCP             = 1 1 6 0  0 13 16 17 18 35 0 0
        ## Emulation value
        EMULATION       = 20.0 0.0
        AVGTYPE         = 1 1 0 0 0
        SECSTOAVG       = 60.0
        ADCALTYPE       = 0 3
        ADCAL           = 1.0 0.0
        ADCAL2          = 10.0 0.0
        ## Temperature slope offset
        COR             = 1.0, 0.0
        ## Conductivity Slope offset
        COR2            = 1.0, 0.0
        ## Nominal Depth of TSG intake below waterline
        COR3            = 3.0

# For FLEAT cruises, which want unaveraged 1Hz TSG data; also change FileWriteInterval to 1.0
[TSG92]
        SENSOR          = Thermosalinograph
        MODEL           = SBE45
        SERIAL          = 0083
        MFG             = Seabird
        CAL_LAB         = Seabird
        CAL_DATE        = 08-Nov-2022
        LOCATION        = Bow thruster UCW intake
        INSTALL_DATE    = 22-Mar-2023
        OWNER           = SIO/STS
        DCC             = FALSE
	DCC_MASK	= 1,1,1,0,0,0,0,0
        LABELS-TAB      = TSG_Temp_BW,TSG_Cond_BW, Salinity_BW,SigmaT_BW,SoundVel_BW,TSG_RCond_BW
        LABELS-SC       = TT_BW,TC_BW, Sal_BW,SgT_BW,SV_BW,TRC_BW
        ## Module setup parameters
        MSP             = 11 3 0 0 10 0 2  2 3 0 0 0 0 0 0
        MCP             = 1 1 6 0  0 13 16 17 18 35 0 0
        ## Emulation value
        EMULATION       = 20.0 0.0
        ADCALTYPE       = 0 3
        ADCAL           = 1.0 0.0
        ADCAL2          = 10.0 0.0
        ## Temperature slope offset
        COR             = 1.0, 0.0
        ## Conductivity Slope offset
        COR2            = 1.0, 0.0
        ## Nominal Depth of TSG intake below waterline
        COR3            = 3.0

[FLW19]
	SENSOR		= Seametrics
	MODEL		= SES-050-13
	SERIAL		= 112018004550
	MFG		= Seametrics
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Bow TSG System
	INSTALL_DATE	= 15-Mar-2019
	OWNER		= SIO/STS
	DCC		= TRUE
        LABELS-TAB      = BwTSGFM
	SLD		= BW
	SAMOS_LD	= L
	## Module setup parameters
	MSP		= 11 3 0 0 10 0 1  13 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  13 0 0 0 0 0 0 0
	## Emulation value
	Emulation	= 13.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## K-Factor	= 1585 PPG
	## Coef = 1.0/((Kfactor/3.7854118)*(1.0/60.0));
	COR		= 0.1433, 0.0

[FLW20]
	SENSOR		= Seametrics
	MODEL		= SES-050-13
	SERIAL		= 112018004549
	MFG		= Seametrics
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Bow PCO2 System
	INSTALL_DATE	= 15-Mar-2019
	OWNER		= SIO/STS
	DCC		= FALSE
        LABELS-TAB      = BwPCO2FM
	SLD		= BW
	SAMOS_LD	= L
	## Module setup parameters
	MSP		= 11 3 0 0 10 0 1  14 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  13 0 0 0 0 0 0 0
	## Emulation value
	Emulation	= 13.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## K-Factor	= 1630 PPG
	## Coef = 1.0/((Kfactor/3.7854118)*(1.0/60.0));
	COR		= 0.1393, 0.0

[SST62]
        SENSOR          = Hull Temperature Sensor
        MODEL           = SBE48
        SERIAL          = 0062
        MFG             = Seabird
        CAL_LAB         = Seabird
        CAL_DATE        = 24-Sep-19
        LOCATION        = Transducer Void
        INSTALL_DATE    = 25-Jan-22
        OWNER           = SIO/STS
        DCC             = TRUE
	DELIMITERS      = \s,ts>
        SAMOS_LD        = U
        LABELS-TAB      = Hull_Temp
        LABELS-SC       = HT_TV
	CMD		= ts\r
        ## Module setup parameters
        MSP             = 4 0 0 1200 10 0 1  1 0 0 0 0 0 0 0
        MCP             = 0 0 1 0  0 0 0 0 0 0 0 0
        ## Emulation value
        EMULATION       =  19.0715, 18 Sep 2016, 19:16:41

[MBD01]
        SENSOR       = Depth Sounder
        MODEL        = EM712
        SERIAL       = 10003
        MFG          = Kongsberg
        CAL_LAB      = n/a
        CAL_DATE     = 2021-06-30
        LOCATION     = Comp Lab
        INSTALL_DATE = 16-Aug-2016
        COMMENT      = Center Beam Depth
        OWNER        = SIO/STS
        DCC          = FALSE
        ## Module setup parameters
        MSP          = 82 14 0 0 10 0 1  1 0 0 0 0 0 0 0
        ## Emulation Value
        Emulation    = 1119
        ## A/D Calibration
        ADCAL        = 1.0 0.0
        ## Corrections
        COR          = 0.0

[MBD02]
        SENSOR       = Depth Sounder
        MODEL        = EM124
        SERIAL       = 119
        MFG          = Kongsberg
        CAL_LAB      = n/a
        CAL_DATE     = 2021-06-30
        LOCATION     = Comp Lab
        INSTALL_DATE = 01-May-2021
        COMMENT      = Center Beam Depth
        OWNER        = SIO/STS
        DCC          = FALSE
        ## Module setup parameters
        MSP          = 83 14 0 0 10 0 1  1 0 0 0 0 0 0 0
        ## Emulation Value
        Emulation    = 1119
        ## A/D Calibration
        ADCAL        = 1.0 0.0
        ## Corrections
        COR          = 0.0

[WCH01]
	SENSOR		= Winch Readouts
	MODEL		= LCI90i
	SERIAL		= ??
	MFG		= Measurement Technology NW
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Computer Lab - Hydro, forward
	OWNER		= RV Sally Ride
	DCC		= FALSE
	## Module setup parameters
	MSP		= 22 3 0 0 10 0 4  5 4 3 1 0 0 0 0
	MCP		= 0 1 4 0  0 0 0 0 0 0 0 0
	## Emulation Value
	Emulation	= 20 60 10000 1
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR		= 1.0 0.0
	COR2		= 1.0 0.0
	COR3		= 1.0 0.0
        LABELS-TAB      = HydroFwd_Payout,HydroFwd_Speed,HydroFwd_Tension

[WCH02]
	SENSOR		= Winch Readouts
	MODEL		= LCI90i
	SERIAL		= ??
	MFG		= Measurement Technology NW
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Computer Lab - Hydro, aft
	OWNER		= RV Sally Ride
	DCC		= FALSE
	## Module setup parameters
	MSP		= 21 3 0 0 10 0 4  5 4 3 1 0 0 0 0
	MCP		= 0 1 4 0  0 0 0 0 0 0 0 0
	## Emulation Value
	Emulation	= 20 60 10000 1
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR		= 1.0 0.0
	COR2		= 1.0 0.0
	COR3		= 1.0 0.0
        LABELS-TAB      = HydroAft_Payout,HydroAft_Speed,HydroAft_Tension

[WCH03]
	SENSOR		= Winch Readouts
	MODEL		= LCI90i
	SERIAL		= ??
	MFG		= Measurement Technology NW
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Computer Lab - Trawl
	OWNER		= RV Sally Ride
	DCC		= FALSE
	## Module setup parameters
	MSP		= 20 3 0 0 10 0 4  5 4 3 1 0 0 0 0
	MCP		= 0 1 4 0  0 0 0 0 0 0 0 0
	## Emulation Value
	Emulation	= 50 10 20000 3
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## Corrections
	COR		= 1.0 0.0
	COR2		= 1.0 0.0
	COR3		= 1.0 0.0
        LABELS-TAB      = Traction_Payout,Traction_Speed,Traction_Tension

[FLU97]
	SENSOR		= Fluorometer
	MODEL		= Wetstar
	SERIAL		= WS3S-797P
	MFG		= Wetlabs
	CAL_LAB		= Wetlabs
	CAL_DATE	= 10-Mar-2021
	LOCATION	= FLO-Thru system Main Lab
	INSTALL_DATE	= 16-Nov-2021
	OWNER		= SIO/STS
	DCC		= FALSE
	SAMOS_LD	= N
	## Range 0.0-27.0 ug/l
	## Module setup parameters
	MSP		= 36 3 0 0 10 0 1  6 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  3 0 0 0 0 0 0 0
	AVGTYPE		= 1
	SECSTOAVG	= 60.0
	## Emulation value
	Emulation	= 2.0
	## A/D Calibration
	ADCAL		=1.0 , 0.0
	## Scale, -Vblank
	#Chlorophyll ug/l
	COR		= 6.5, -0.075

[FLU02]
	SENSOR		= Fluorometer
	MODEL		= FLUNTS
	SERIAL		= 4402
	MFG		= Wetlabs
	CAL_LAB		= Wetlabs
	CAL_DATE	= 13-Apr-2021
	LOCATION	= FLO-Thru system Main Lab
	INSTALL_DATE	= 16-Nov-2021
	OWNER		= SIO/STS
	DCC		= FALSE
	SAMOS_LD	= N
	TAGS-R		= FL TB
	TAGS-C		= FL TB
	## Range 0.0-50.0 ug/l 0-25NTU
	## Module setup parameters
	MSP		= 37 3 0 0 10 0 2  4 6 0 0 0 0 0 0
	MCP		= 1 1 2 0  3 3 0 0 0 0 0 0
	AVGTYPE		= 1
	SECSTOAVG	= 60.0
	## Emulation value
	Emulation	= 2.0
	## A/D Calibration
	ADCAL		=1.0 , 0.0
	## Scale, -Vblank
	#Chlorophyll ug/l
	COR		= 0.0138, -49.0
	#NTU
	COR2		= 0.0272, -51.00

[FLU81]
	SENSOR		= Fluorometer
	MODEL		= ECO Triplet-w
	SERIAL		= 1481
	MFG		= Wetlabs
	CAL_LAB		= Wetlabs
	CAL_DATE	= 03-May-2018
	LOCATION	=  FLO-Thru system Main Lab
	INSTALL_DATE	= 07-Aug-2018
	OWNER		= SIO/STS
	DCC		= FALSE
	SAMOS_LD	= Y
	TAGS-R		= XX XX XX
	TAGS-C		= XX XX XX
 	LABELS-TAB      = cp(m-l), Phycoerythrn, CDOM(ppb)
        LABELS-SC       = cp, Phy,CDOM
	## Scattering (beam cp(m-l)), Phycoerythrin(ppb), CDOM (ppb)
	## Module setup parameters
	MSP		= 38 3 0 0 10 0 3  4 6 8 0 0 0 0 0
	MCP		= 1 1 3 0  3 3 3 0 0 0 0 0
	AVGTYPE		= 1
	SECSTOAVG	= 60.0
	## Emulation value
	Emulation	= 2.0
	## A/D Calibration
	ADCAL		=1.0 , 0.0
	## Scale, -Vblank
	# beam cp(m-l)
	COR		= 7.775e-6, -50.0
	#Phycoerythrin(ppb)
	COR2		= 0.0401, -63.0
	# CDOM (ppb)
	COR3		= 0.0848, -47.0

[FLW09]
	SENSOR		= Seametrics
	MODEL		= SPX-038-01
	SERIAL		= 032017002317
	MFG		= Seametrics
	CAL_LAB		= n/a
	CAL_DATE	= n/a
	LOCATION	= Main Lab Flo-thru System
	INSTALL_DATE	= 27-Oct-2022
	OWNER		= SIO/STS
	DCC		= TRUE
	TLD		= MAIN
	SLD		= ML
	SAMOS_LD	= N
	## Module setup parameters
	MSP		= 36 3 0 0 10 0 1  13 0 0 0 0 0 0 0
	MCP		= 1 1 1 0  13 0 0 0 0 0 0 0
	## Emulation value
	Emulation	= 13.0
	## A/D Calibration
	ADCAL		= 1.0 0.0
	## K-Factor	= 1266 PPG
	## Coef = 1.0/((Kfactor/3.7854118)*(1.0/60.0));
	COR		= 0.1794, 0.0

[OXY66]
        SENSOR          = Oxygen
        MODEL           = SBE-63
        SERIAL          = 1194
        MFG             = Seabird
        CAL_LAB         = Seabird
        CAL_DATE        = 28-Jan-2021
        LOCATION        = FLO-Thru system Hydro Lab
        INSTALL_DATE    = 10-Feb-2021
        OWNER           = SIO/STS
        DCC             = FALSE
        SAMOS_LD        = N
        TAGS-R          = OT OX
        TAGS-C          = OT OX OS
        DCC_MASK        = 1,1,0,0,0,0,0,0
        ## Module setup parameters
        MSP             = 39 3 0 0 10 0 2  4 1 0 0 0 0 0 0
        MCP             = 1 1 3 0  0 45 23 0 0 0 0 0
        ## Emulation value
        Emulation       = 24.3279 16.443
        ## A/D Calibration
        ADCAL           = 1.0, 0.3
        ## Corrections Oxygen Temp
        COR             = 1.0, 0.0
        ## Corrections Oxygen
        COR2            = 1.0513, -1.5e-3, 3.3019e-1, -2.3209e-1, 1.5663, 9.48086e-2, 4.0696e-3, 6.1627e-5, 1.1e-2


[OXY99]
	SENSOR		= Oxygen
	MODEL		= SBE-43
	SERIAL		= 1194
	MFG		= Seabird
	CAL_LAB		= Seabird
	CAL_DATE	= 28-Jan-2021
	LOCATION	= FLO-Thru system Hydro Lab
	INSTALL_DATE	= 10-Feb-2021
	OWNER		= SIO/STS
	DCC		= FALSE
	SAMOS_LD	= N
	TAGS-R		= OT OX
	TAGS-C		= OT OX OS
        DCC_MASK        = 1,1,0,0,0,0,0,0
	## Module setup parameters
	MSP		= 36 3 0 0 10 0 2  7 8 0 0 0 0 0 0
	MCP		= 1 1 3 0  0 34 23 0 0 0 0 0
	## Emulation value
	Emulation	= 24.3279 16.443
	## A/D Calibration
	ADCAL		= 1.0, 0.3
	## Corrections Oxygen Temp
	COR		= 1.0, 0.0
	## Corrections Oxygen
	COR2		= 0.4720,-0.4956,1.10,-4.4424e-003,9.9896e-005,-58867e-007,0.036

[TSG73]
	SENSOR		= Thermosalinograph
	MODEL		= SBE45
	SERIAL		= 0575
	MFG		= Seabird
	CAL_LAB		= Seabird
	CAL_DATE	= 09-Feb-2023
	LOCATION	= Main Lab
	INSTALL_DATE	= 21-Mar-2023
	OWNER		= SIO/STS
	DCC		= TRUE
        DCC_MASK        = 1,1,1,0,0,0,0,0
	SAMOS_LD	= N
	TLD		= ML
	SLD		= ML
	## Module setup parameters
	MSP		= 36 3 0 0 10 0 2  2 3 0 0 0 0 0 0
	MCP		= 1 1 6 0  0 13 16 17 18 35 0 0
	## Emulation value
        SECSTOAVG       = 60.0
        ADCALTYPE       = 0 3
        ADCAL           = 1.0 0.0
        ADCAL2          = 10.0 0.0
        ## Temperature slope offset
        COR             = 1.0, 0.0
        ## Conductivity Slope offset
        COR2            = 1.0, 0.0
        ## Nominal Depth of TSG intake below waterline
	EMULATION	= 20.0 5.0
	AVGTYPE		= 1 1 0 0 0
	SECSTOAVG	= 60.0
	ADCALTYPE	= 0 3
	ADCAL		= 1.0 0.0
	ADCAL2		= 10.0 0.0
	## Temperature slope offset
	COR		= 1.0, 0.0
	## Conductivity Slope offset
	COR2		= 1.0, 0.0
	## Nominal Depth of TSG below waterline
	COR3		= 0.0

# For FLEAT cruises, which want unaveraged 1Hz TSG data; also change FileWriteInterval to 1.0
[TSG98]
	SENSOR		= Thermosalinograph
	MODEL		= SBE45
	SERIAL		= 0575
	MFG		= Seabird
	CAL_LAB		= Seabird
	CAL_DATE	= 09-Feb-2023
	LOCATION	= Main Lab
	INSTALL_DATE	= 21-Mar-2023
	OWNER		= SIO/STS
	DCC		= FALSE
        DCC_MASK        = 1,1,1,0,0,0,0,0
	TLD		= ML
	SLD		= ML
	## Module setup parameters
	MSP		= 36 3 0 0 10 0 2  2 3 0 0 0 0 0 0
	MCP		= 1 1 6 0  0 13 16 17 18 35 0 0
	## Emulation value
	EMULATION	= 20.0 5.0 
        ## AVGTYPE      = commented out for FLEAT, normally 1 1 0 0 0
        ## SECSTOAVG    = 01.0 (e.g. no averaging, commented out for FLEAT) normally 60.0
        SECSTOAVG       = 60.0
        ADCALTYPE       = 0 3
        ADCAL           = 1.0 0.0
        ADCAL2          = 10.0 0.0
        ## Temperature slope offset
        COR             = 1.0, 0.0
        ## Conductivity Slope offset
        COR2            = 1.0, 0.0
        ## Nominal Depth of TSG intake below waterline
	ADCALTYPE	= 0 3
	ADCAL		= 1.0 0.0
	ADCAL2		= 10.0 0.0
	## Temperature slope offset
	COR		= 1.0, 0.0
	## Conductivity Slope offset
	COR2		= 1.0, 0.0
	## Nominal Depth of TSG below waterline
	COR3		= 0.0

[XMS76]
        SENSOR          = Transmissometer
        MODEL           = C-Star
        SERIAL          = CST-1176DR
        MFG             = Wetlabs
        CAL_LAB         = Wetlabs
        CAL_DATE        = 07-Sep-2021
        LOCATION        = Main Lab
        OWNER           = SIO/STS
        DCC             = FALSE
        INSTALL_DATE    = 07-Sep-2022
        ## Wetlabs Cstar
        ## Module setup parameters
        MSP             = 36 3 0 0 10 0 1  5 0 0 0 0 0 0 0
        MCP             = 1 1 2 0  38 39 0 0 0 0 0 0
        ## Emulation value
        Emulation       = 3.56
        ## A/D Calibration
        ADCAL           = 1.0, 0.0
        ## A0, Y0, A1, Y1, W0, z
        COR             = 4.782, 0.066, 4.782, 0.066, 4.685, 0.25
        A0              = factory voltage output in air (factory calibration from transmissometer manufacturer)
        Y0              = factory dark or zero (blocked path) voltage (factory calibration from transmissometer manufacturer)
        A1              = current (most recent) voltage output in air
        Y1              = current (most recent) dark or zero (blocked path) voltage
        W0              = factory voltage output in pure water (factory calibration from transmissometer manufacturer)
        z               = Path Length in Meters

[USP01] #CalCOFI PCO2
        SENSOR          = PCO2
        MODEL           = Super-PCO2
        SERIAL          = ????
        MFG             = ???
        CAL_LAB         = n/a
        CAL_DATE        = n/a
        LOCATION        = Ocean Lab
        INSTALL_DATE    = 31-Mar-2015
        OWNER           = Science
	DCC		= FALSE
        #DOY_UTC, pH, CO2_ppm, Valve_Pos, TSG_Temp, TSG_S
        TAGS-C          = XX,PH,XX,XX,TT,SA
        TAGS-R          = XX,PH,XX,XX,TT,SA
        PRC-C           = 6 6 3 0 4 4
        PRC-R           = 6 6 3 0 4 4
        LABELS-TAB      = pc_DOY,pc_PH,pc_CO2,pc_Valve,pc_TMP,pc_SLT
        LABELS-SC       = pcDY,pcPH,pcCO,pc_VP,pcT,pcS
        # Module address         
        # Module setup parameters        
        MSP             = 43 3 0 0 10 0 6 1 2 3 4 5 6 0 0
        MCP             = 1 1 6 0  0 0 0 0 0 0 0 0
        #64.555323      8.125004        467.844 1       18.0287 34.31
        Emulation       = 64.555323     8.125004        467.844 1       18.0287 34.31
        # A/D Calibration        
        ADCAL           = 1.0, 0.0
        # Corrections    
        COR             = 1.0 0.0

[UCW01]
        SENSOR          = UCW Pumps
        MODEL           = ????
        SERIAL          = ????
        MFG             = ???
        LOCATION        = Bow RM/Port sea-chest
        INSTALL_DATE    = 25-Feb-2021
        OWNER           = STS
	DCC		= TRUE
	SAMOS_LD	= U
        MSP             = 29 25 0 0 10 0 1 1 2 0 0 0 0 0 0
        MCP             = 1 1 1 0  0 0 0 0 0 0 0 0
#	1.Bow Pump    2. Port Sea-chest
#	0=Pump Off   1= Pump On
	Emulation	= 1